Extruder screws

PRODUCTS

BIMETALIC LINER(SLEEVE)

Product Description: Twin Extruder Liner Materials: OS02H(Ni-Cr-W Alloy) , other
Description Warranty Info
Description

Product Description: Twin Extruder Liner

Materials: OS02H(Ni-Cr-W Alloy) , other required Alloy  

Hardness:  Different based on differeent materials  

ApplicationInside of Parallel Twin Extruder barrel

Charactors:  High Wear-Resistance, High Corrosion Resistance 

Product Introduction

Linner is usually used inside of the barrrel , near to the screw elements, So its inner wall is easily worn and corroded by materials


New Materials Introduction

Based on long years of  experience for the manufacturing, in order to long last the service life of the liner or barrel liner, we developed our special new materials OS02H , a kind of Nickel-Chromium- Tungsten alloy.

Nickel-Chromium- Tungsten alloy has excellent abrasion resistance and corrosion resistance. The increase of Cr content in the nickel-chromium alloy matrix contributes to the oxidation resistance, high temperature resistance and corrosion resistance of the alloy. At the same time, the addition of CrB is better than WC. The microhardness of CrB is as high as 4000-4200DPH, which is close to diamond. It is more conducive to improving the overall strength of the alloy. Due to the high density of WC, it is about 15.7g/cm3, while the matrix of nickel-chromium alloy is only about 8g/cm3. The melting is caused by the uneven surface and depth of the alloy due to the easy segregation of WC, so the content and particle size of WC must be controlled.

Nickel-Chromium-Tungsten alloy( we call OS 02H) hard phase increased to about 50%, OS02 is only ten to thirty,Moreover, the fusion is not sufficient, and the microscopic pores are relatively obvious, which is reflected by the Rockwell hardness HRC of only 52-55.While the Rockwell hardness of nickel chromium tungsten alloy (OS02H) is HRC56-64, the conventional control is HRC58-60. The service life is 3-5 times longer then WR5 or CPM10V.

Nickel-Chromium-Tungsten alloy( OS02H )on the basis of Ni60 in accordance with foreign twin screw working conditions of the formula, greatly improved Hard phase carbides (containing tungsten carbide chromium carbide and other carbides), and the nickel pool fullDissolve. Our Ni-Cr -W alloy layer can reach HRC64 is the best proof.

Liner Types

Single metal liner,

Bimetallic compound liner,

Sintered process composite liner

spray welding process composite liner.

图片1.png

图片2.png

图片3.png

Bimetallic Compound Liner Features:

Material Parameters Temperature Resistance:

Temperature limit 600℃

Alloy Layer Thickness: ≧1.8mm

 Alloy Layer Hardness: 57-64HRC

The Main Process Is Different (from the original sintering process to the current spray welding process) The product has better densification, the hardness can reach more than 57 degrees, and the service life of the product is 3-5 times that of the sintering process.

图片3.png123.png

Main Brands Extruder for using the Liner

Twin screw elements available for the following brands

Clextral

KraussMaffei

Leistritz

JSW

Buhler

Toshiba

Coperion

Berstorff

Maris

KOBE

Wenger

CPM




Production Equipments

At present, the company's factory area exceeds 3000 square meters, and an additional 3000 square meters are under planning and design, covering the complete production process of material research and development, main component production, and testing. The company has 6 technical personover 40 workers, and multiple imported production and testing equipment from Taiwan and Germany. 

图片1.png

微信图片_20220719095117.jpg

微信图片_20220719095107.jpg

Quality Control

The Test Equipments we have now are as follows:
 three coordinate detectors,  dimensional image measuring instruments,  metallographic analyzer,  ultrasonic flaw detector,  element analyzer and many other basic test machines. Which can fully confirm the quality we offered .
 

图片10.png

图片10.png

图片9.png

Why Choose US

1)  Independent research and development of materials and processes can ensure the performance and process of materials to the maximum extent, and greatly prolong the service life compared with ordinary products, while the main supplier in the market only buy raw materials for machining. 

图片11.png

2) Independently develop the process of key products, and constantly improve and enhance the old process to achieve the best product performance.

 For example, we changed  the production process for barrel liner and liner from sintering to spray welding.  Which increased the product service life 3-5 times then normal products. 

图片12.png


3)Continuously improving and optimizing product appearance of the composite layer which greatly improved the service life of products.for the separately linner and Barrel Liner, we changed the Composite layer from thin 8 shape to ellipse flat angle shape, which increased the product service life greatly. 

图片13.png

Choose Bloom, Choose a Qualifed Supplier!

Welcoming for inquiring at any time! 



Warranty Info

123

Send your message to us